Welcome to my blog which follows my furniture restoration business. Please feel free to comment at the bottom of the post, and if you would like a response please leave your email address. you can also contact me directly at info@johnmarkpower.com. And by all means, if you like something please feel free to share it.

Monday, April 9, 2012

Reproduction Walnut Hall Tree Part 3: Assembling The Hall Tree

This is the third post concerning the reproduction of a 19th century hall tree. The previous two post have dealt with designing and making individual components. This third post will follow along with more of the same as well as show the assembling of all of the components to make the hall tree. One thing that always surprises me when constructing a piece of furniture is the interrelation of all of the individual components. If a change is made or an error occurs, the result affects the entire piece. Sometimes this is a change for the better or an error that can be corrected, and other times it can have deeper consequences, like having to make a new part from scratch. I liken the process to walking on a tight rope. It requires concentration and a steady, focused hand to persevere. That being said, mistakes inevitably happen and it is good to know how to deal with them when they occur. Now enough with the philosophy, and on to the project!

There were several components that I decided not to draw in SketchUp (see first post) but rather to copy directly from the piece. These were appliques that were superficial to the construction of the piece, but enhanced the design of the hall tree. The first of these was a piece of molding that had an edge consisting of half circles cut into a cove. The Molding is pictured below:
The first step was to make the portions of the molding made by the router. This consisted of the decorative lines running from side to side and the cove itself. This was a very small piece of molding in terms of width, so I left a lot of extra waste material so I could have better control of the piece as I worked on it and also I could keep my hands away from the machinery. Once the routed parts were completed, I flipped the board over and drew the half circles on the back side of the cove using a compass. This next photo shows the half circle layout on the back of the board.
I then took the piece to the band saw and cut the circles out. The photo below shows what that looks like. After that the last step was to remove the extra waste material by ripping it on the table saw.
On either side of this molding is an applique that works as a transition piece from the molding to the frame of the hall tree. It's purpose is solely visual. Below is a photo of one of these pieces followed by another photo showing the pieces made for the reproduction. The profile of these pieces were cut out on the band saw.

Next to those pieces, and applied to the sides of the hall tree, were some decorative pieces with carved hints of a volute. All of the carving on this piece was simple and were typical of factory carving of the time. The intention was to add decoration and to hint at the idea of a highly carved piece. Most of the carving was shallow and was similar to drawing. The original applique is pictured below followed by the ones I made for the reproduction.

These last applied components are found in the middle of the hall tree and flank the central raised panel on either side. There were cut out on the band saw and then little turned domes were applied to the faces of the components. here is a photo of one of the originals.

Here are the two pieces for the reproduction after being cut on the band saw.
This photo shows the applied domes being glued in place.
This photo shows the finished product.
Now that all of the applied pieces were made it was time to assemble the hall tree. The first step in this was to take all of the rails and stiles and lay them out on top of each other with the tenons overlapping the piece it would mortise into. This allowed me to accurately layout where the mortises were going to be. Below is a detail photo showing this. Rather than being flat, the pieces were stacked so I could trace around the tenons on to the face of the piece below it. The photo that follows shows the entire back assembled in this fashion.

After the mortises were all cut, I dry-assembled the back to make sure everything fit together nicely. The next photo shows this. It is followed by a photo of the rails and stiles for the bench assembled. This was an exciting moment because for the first time I was looking at an assembled item versus a pile of parts!

After all of the mortice and tenon joints were test fitted and fine tuned, I fit the raised panels in place and fine tuned their joinery as well. This photo shows the frame dry-assembled with the panels in place.
Before gluing the back together, I needed to apply some wood to the long back stiles that would stiffen these stiles up and help keep the back straight. I wanted these piece to be straight and in a search for a flat surface to glue them on, I remembered a lathe in the shop with a seven foot bed. The bed provided the flat surface I needed so I glued these strips together clamped to the bed. Below are two photos of this process.

After that was completed, I removed the clamps and glued the hall tree together. There were a few appliques as well as the seat I left out, but most of the gluing happened at this time. Below is a photo of the hall tree clamped while the glue was setting followed by a photo of the hall tree standing on it's own four feet!

The next step was to make the lid for the box at the bottom of the case which would also act as the seat. This lid comprised of a frame that went around the back and sides of the lid and the lid itself, which had breadboard ends to strengthen the lid. Below is a photo of the breadboard ends being glued to the lid.
Once the glue dried on the lid the clamps were removed and the ends of the breadboard ends trimmed. The next step was to attach the hinges to the lid and the board that went across the back. After the hinges were in place, the boards which frame the lid on the sides were glued on to the back. I glued them using the hall tree so that they would match the rest of the piece as well as possible.
Now that the entire seat was assembled, I needed to produce the rounded molding along the edge of the seat. The next two photos show the seat set up for this procedure. I clamped boards on either end of the seat to run into with the router. This prevented grain tear out and the boards were discarded after they had served there purpose.The last photo in the set shows the seat with the molded edge.



The last step in the assembling process was to attach the seat and arms to the hall tree. The arm posts had turned tenons which joined them to the seat and the arms. The seat and the arms were attached to the back with screws and I used dowels to attach the seat to the seat frame below. The photo below shows the seat and arms being glued in place. It is followed by two photos of the fully assembled hall tree. The next and final post will deal with the application of the finish and show the final product!

One note: I have left the lion carvings that are featured in the first post off of the hall tree in these photos because with the lions in place, the Hall tree is too tall to stand in my shop!


Thursday, March 15, 2012

Reproduction Walnut Hall Tree Part 2: Milling, Turning, and Carving

This is the second post I am writing concerning the reproduction of a hall tree dating to around 1890. The original was made of Oak but I am making the reproduction from Walnut. The first post was concerned with the reproduction of the pediment and the lion carvings that sit on it's perch. In this post I will show some of the turning and carving work as well as a some of the milling work.

With the exception of a few panels, I was able to make the entire piece up from solid material. The panels were glued up from two boards and are used for the center raised panel, the back of the case below the seat, and the bottom of the case below the seat. The photo below shows most of the pieces for the hall tree cut to size. It is followed by two photos of the panels that I glued up being clamped while the glue dries.


One of the nice things about this project is that it requires a diversity of skills. There is turning, carving, joinery, and molding involved in the reproduction. These next few photos document some of the turning that was done for the project.

The hall tree has three vertical turnings that pierce one of the rails in the back. They are purely decorative. The turnings are actually made up of two different turnings which are tenoned into the rail, one below and one above. The turnings below are vase shaped and terminate with a tenon in the rail below. The turnings above the top rail are arrow shaped and terminate midway between rails. Below are a few photos of the bottom turnings being turned.

The turning blank is chucked into the lathe and ready to turn.
In this photo the blank is turned to a rough billet allowing me to mark where my cuts will be.
this photo was taken during the turning process.
The finished turning.
The last step before parting the turning off was to turn the tenons on either end.
This photo shows the three turnings together.
These next few photos show the turning of the arrow points above the rail. Unfortunately the photos were uploaded sideways and I cannot fix them, but you get the idea.

This photo shows one of the arrow heads being turned.
Here I am comparing one of the turnings to an original from the Oak hall tree.
The three turned arrowhead completed.
The next two photos show before and after shots of the caps that cap the arm posts on the seat. The post is tenoned through the arm and the cap covers the end of the tenon. The entire assembly can be seen at the end of this post.

Before...
....and after.
I also turned several smaller caps which are used as decoration on another part of the hall tree. I neglected to take photos of them so I will move ahead to the arm posts.

Here is a photo of the arm post blank before it was turned followed by a photo of it after it was turned.
the last turning that was necessary was to decorate the center of a raised panel. Rather than applying decoration to the panel, the original craftsman decided to turn the entire panel and then to carve it. The result is a carving of a sunflower in the center flanked by cattails in each corner. The following photos show the preparation, turning, and carving of the raised panel.

This photo shows a backing board being glued to the back side of the panel. This step was made on the original hall tree and serves the purpose of making the center carving sturdier. It also made the blank more rigid for turning.

after the glue dried, I positioned the faceplate on the back of the raised panel. In the center of the faceplate is a Forstner bit I used to help center the faceplate. Once centered, the faceplate was screwed to the blank and the Forstner bit was removed.

The next two photos show the raised panel attached to the lathe and ready to turn. The dimensions of the panel were 13" x 13" x 5/8". From corner to corner the panel was around 18". This was a large piece to turn and I made sure everything was very secure before I fired up the lathe. When I did the blank was balanced and caused little vibration. To see a video of me turning the design, follow this link:

http://www.youtube.com/watch?v=5ti9EVJPJIA&context=C4da8a75ADvjVQa1PpcFNgAZa2gGJNRYlg5-sfBhORXXDPNRVeTjM=


This next photo shows what the turned sections looked like after I had finished on the lathe.
I next marked out the turned area so that I could carve the detail. This included carving the larger circle into flower petals.
This photo was taken during the carving process. I had also cut the sides away on the table saw to create the raised panel.
These next three photos show the completed panel. The last photo shows the new panel next to the old.


The last part I will write about in this post is the fabrication of the arms. This was fairly straight forward. I created a template that I could use for both arms and traced it's profile onto the wood I had chosen for the arms. Below is a photo of the template laid out. I used a Forstner bit to drill the hole so I could use it again on the actual arms to find the center for drilling.
This photo shows both arms cut out before they were drilled.
Once the hole was drilled, I assembled the arms with the arm posts and caps. As mentioned before, the arm post has a long tenon that passes through the arm and into the underside of the cap. Here is a photo of the completed arm assembly followed by a photo of both arm assemblies.

This last photo shows the corner blocks which transition into the back of the hall tree being glued in place. I use the table saw fence as a clamp here.
the next post will show the construction of the hall tree.